Case 13 — Strap dimensions: lug width, taper, thickness and spring bar diameter explained
Summary order of importance. 1) Lug width, measured between the lugs. 2) Lug-end thickness against clearance. 3) Spring bar diameter. 4) Taper and buckle width. 5) Length, which is usually given as long side / short side in mm and should be compared with a strap that already fits you.
Clarification for “Comparing versions without mixing case sizes”: the point beginning “Match reference, dimensions and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 26 — Maintenance question: how do I tell if an automatic actually needs service?
Clarifying question first: do you have a baseline? If you've never recorded the watch's rate or power reserve, 'drifting' is hard to judge. Start a simple log now with daily offset against a reference time for a week, and the hours it runs from full wind. Once you have that, later changes mean something.
Clarification for “Comparing dial colour under different lighting”: the point beginning “State the lighting and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 41 — Service enquiry: information a watchmaker can use · source wording exercise
Method note for “Service enquiry: information a watchmaker can use”: use “Be honest about the watch and request an assessment…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.
Case 40 — Shipping timeline: separate dispatch, handover and scan events · source wording exercise
Method note for “Shipping timeline: separate dispatch, handover and scan events”: use “Ask the sender or carrier for clarification; missing scans alone…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.
Case 14 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log
I'm putting together a side-by-side of the 38mm and 40mm versions of a common three-hand field watch design. The aim is a reference post we can fix over time instead of repeating the same arguments. Corrections go in a dated log at the bottom. What should the table include besides case diameter, and which specs are usually misreported?
Exercise RWF-26484/14: address this question within its stated limits.
Method note for “Service enquiry: information a watchmaker can use”: use “Document when it stops, winding behaviour, recent impacts and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Ask for photographs with the light moved and retain the same viewing angle. A mark should be assessed across multiple views; aggressive polishing is not an appropriate diagnostic test.
Case 52 — Movement identification: the limits of a rotor photograph · source wording exercise
Only part of the movement is visible and the rotor hides several bridges. Which details can be described without claiming certainty?
Review focus: source wording. Retain the source wording beside any paraphrase. Use the original answer fragment “Ask a qualified watchmaker to inspect it if identification matters for…” as the discussion anchor; no new event or result is supplied.
Exercise RWF-22395/52: address this question within its stated limits.
Case 35 — Case finishing: distinguish a reflection from a surface mark
Limit of the answer in “Case finishing: distinguish a reflection from a surface mark”: “Ask for photographs with the light moved and…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.
Separate three properties: click count (60 or 120 positions), feel (how firm each click is, and whether there's back-play), and alignment (whether the pip lines up with the 12 o'clock marker at rest). Crisp vs mushy is mostly about feel and back-play. Alignment can be measured, so treat it separately.
Match reference, dimensions and configuration first. List confirmed differences separately from seller descriptions and date the comparison so later readers understand its scope.
Request a level straight-on image with the hands clear of the marker. Compare two independently aligned images before drawing a conclusion; an overlay cannot correct an oblique camera angle.
Describe visible bridge shapes and markings separately from the proposed identification. Ask a qualified watchmaker to inspect it if identification matters for servicing; do not open the case merely for a forum answer.