Case 21 — Forum comparison archive: link the evidence and the correction
Clarification for “Forum comparison archive: link the evidence and the correction”: the point beginning “Add a dated correction near the original conclusion…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 18 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log
Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.
Summary. Pick sapphire for scratch resistance in low-impact use, acrylic for impact tolerance and easy polishing, and mineral as a low-cost middle option. Prefer inner-surface AR if you're worried about wear. Look at crystal profile when comparing thickness. Choose by how you'll use the watch, not by the material label.
Record wrist circumference, removable links and the clasp adjustment range in millimetres. Request the closed bracelet circumference rather than inferring it from marketing dimensions.
Case 21 — QC photography: what photos actually help verify a pre-owned listing?
Clarifying question for the thread: is the goal to check authenticity, condition, or both? For condition, the request list above is enough. For authenticity, you also need caseback, serial or reference engravings, and ideally movement photos. Movement photos usually require opening the watch, which a seller may reasonably refuse without a watchmaker present.
Case 28 — Clasp photographs: what to request before judging alignment
Correction note for “Clasp photographs: what to request before judging alignment”: retain the wording beginning “Request open and closed views from both sides,…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 12 — QC photography: what photos actually help verify a pre-owned listing?
Ask for profile shots of both case sides and a lug-top shot at an angle. Polishing shows as rounded edges, softened bevels or lug holes that look shallower than they should. Compare against a known-good reference image of the same model, not memory. A side-by-side tells you far more than a description.
Case 31 — Lug-to-lug and end-link overhang in wrist photographs
Clarification for “Lug-to-lug and end-link overhang in wrist photographs”: the point beginning “Record lug-to-lug and the effective span…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Lug width is the essential one: the inside distance between the lugs where the strap fits. Measure with a ruler marked in millimetres, ideally reading it under magnification. Most watches use even numbers (18, 20, 22mm), but odd widths exist. If you measure 19 or 21, measure again and check the manufacturer spec before ordering.
Correction note for “Strap dimensions: lug width, taper, thickness and spring bar diameter explained”: retain the wording beginning “Lug width is the essential one: the inside distance between…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
State whether thickness includes the highest point of a domed crystal. Different measurement methods can produce different figures, so keep both the source and method beside each dimension.
Clarifying question: does anyone in the thread have access to both versions at once? Without simultaneous comparison, every claim either way is weak evidence. If not, the next best option is photos with a grey card in frame and white balance locked or set manually, which at least makes separate photos roughly comparable.
Case 26 — Maintenance question: how do I tell if an automatic actually needs service?
Keep a baseline log, describe changes in rate or running time and stop forcing rough winding. Follow the manufacturer’s guidance and arrange professional assessment when operation changes. A forum cannot prescribe a universal service interval.
Case 33 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log
Use a correction row with date, old value, revised value and evidence. A worked example could change a lug-width entry from 20 to 22 mm; do not present that example as a correction to a real model.
Case 20 — Magnetism and rate: record evidence before naming a cause
Summary draft for “Magnetism and rate: record evidence before naming a cause”: the answer addresses “Record the change and the circumstances without treating…”; the related point is “A competent watchmaker can test and diagnose it; random adjustment…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.