Case 24 — Model comparison: dive bezel action and alignment, how to compare fairly
On alignment, a clarifying point: is the misalignment visible straight on, or only from an angle? Parallax on a raised bezel can make a perfectly aligned pip look half a click off when viewed slightly from the side. Photograph straight above the dial before calling it misaligned.
Clarification for “Reading a timegrapher recording without losing the context”: the point beginning “Keep the complete recording and ask for the…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 9 — Timegrapher reading context: what do rate, amplitude and beat error actually tell me?
I ran a watch on a basic timegrapher and got +6 s/d, 245 degrees amplitude and 0.8 ms beat error, dial up, about an hour after winding. Is this good, bad or normal? I don't want to send it for service on a single reading.
Exercise RWF-30919/9: address this question within its stated limits.
Clarification for “QC photographs: perspective or a genuinely tilted index?”: the point beginning “Request a level straight-on image with the hands…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 14 — QC checklist: prioritise observable faults over pixel hunting
Summary draft for “QC checklist: prioritise observable faults over pixel hunting”: the answer addresses “Start with function, legibility, assembly and…”; the related point is “Explain what the full-size image shows, what the crop adds and…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Case 22 — Maintenance question: how do I tell if an automatic actually needs service?
A sudden rate change has several possible causes. Ask a watchmaker to test suspected magnetism rather than diagnosing it from a compass or attempting an adjustment based on forum replies.
Case 21 — Forum comparison archive: link the evidence and the correction
A comparison has been corrected after a new photograph arrived. How should the original thread remain useful?
Exercise RWF-28599/21: address this question within its stated limits.
Case 17 — First QC request: the minimum useful information
Summary draft for “First QC request: the minimum useful information”: the answer addresses “State the model configuration, the specific concern and…”; the related point is “Include complete instrument settings where relevant and say…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Domed crystals of any material add distortion at the edges, which some people like and others find hard to read at angles. Box-shaped or high-domed crystals also add thickness. If you're comparing two otherwise similar watches, check total thickness against crystal profile before assuming the case itself is thicker.
Clarification for “Reading a timegrapher recording without losing the context”: the point beginning “Keep the complete recording and ask for the…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 21 — QC photography: what photos actually help verify a pre-owned listing?
Ask for a straight-on dial photo with diffuse light and no flash, the full dial in frame, and the hands placed away from the indices (10:10 isn't ideal, because it covers the upper markers). Flash flattens printing and hides lume condition. Diffuse light shows print edges, alignment and any spotting.
Case 28 — Clasp photographs: what to request before judging alignment
Method note for “Clasp photographs: what to request before judging alignment”: use “Request open and closed views from both sides,…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Case 12 — QC photography: what photos actually help verify a pre-owned listing?
When asking a seller for extra photos of a pre-owned watch, what shots are actually useful as evidence? Listings tend to have glossy angled photos that hide more than they show. I'd like a standard request list the forum can reuse.
Exercise RWF-21341/12: address this question within its stated limits.
Case 31 — Lug-to-lug and end-link overhang in wrist photographs
A wide-angle wrist photo exaggerates the nearest edge of the case. How can two watches be compared fairly?
Exercise RWF-20114/31: address this question within its stated limits.
Wrist size changes during the day and with temperature, sometimes by several millimetres. A fit that feels tight in the afternoon may be right in the morning. Before buying parts, check the fit at different times. You may find the 'too tight' setting is only a problem a few hours a day.