Case 14 — QC checklist: prioritise observable faults over pixel hunting
Correction note for “QC checklist: prioritise observable faults over pixel hunting”: retain the wording beginning “Start with function, legibility, assembly and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 22 — Maintenance question: how do I tell if an automatic actually needs service?
If the manufacturer provides a suitable procedure, a running-time log can support a service enquiry. State the winding method and stop time. A shortened run does not identify the cause by itself.
Case 20 — Crystal reflections: why a dark patch is not a coating test
Summary draft for “Crystal reflections: why a dark patch is not a coating test”: the answer addresses “No single lighting setup settles…”; the related point is “Compare multiple controlled angles and describe the visible observation without asserting…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Case 17 — First QC request: the minimum useful information
Correction note for “First QC request: the minimum useful information”: retain the wording beginning “State the model configuration, the specific concern and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
On anti-reflective coatings: inner-surface AR cuts glare without wear concerns. Outer-surface AR improves legibility further but can scuff over time, and the scuffs show up as hazy patches in certain light. When comparing two watches, check which surfaces are coated. Spec sheets often just say 'AR coated' without saying where.
Keep the complete recording and ask for the settings, winding state and position. A single number cannot establish service condition, movement identity or performance on a wrist.
Case 21 — QC photography: what photos actually help verify a pre-owned listing?
When asking a seller for extra photos of a pre-owned watch, what shots are actually useful as evidence? Listings tend to have glossy angled photos that hide more than they show. I'd like a standard request list the forum can reuse.
Exercise RWF-23960/21: address this question within its stated limits.
Case 28 — Clasp photographs: what to request before judging alignment
Clarification for “Clasp photographs: what to request before judging alignment”: the point beginning “Request open and closed views from both sides,…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 11 — Timegrapher reading context: what do rate, amplitude and beat error actually tell me?
The reported numbers alone do not establish damage or the need for service. Confirm the setup, collect comparable readings and ask a watchmaker to assess a concerning or changing pattern.
Case 30 — Service enquiry: information a watchmaker can use
Summary draft for “Service enquiry: information a watchmaker can use”: the answer addresses “Document when it stops, winding behaviour, recent impacts and…”; the related point is “Be honest about the watch and request an assessment…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Micro-adjust spacing varies by clasp. Measure the actual change at each setting rather than assuming a standard number of millimetres; compare the usable range with the link length.
Ask for profile shots of both case sides and a lug-top shot at an angle. Polishing shows as rounded edges, softened bevels or lug holes that look shallower than they should. Compare against a known-good reference image of the same model, not memory. A side-by-side tells you far more than a description.
Clarification for “Strap dimensions: lug width, taper, thickness and spring bar diameter explained”: the point beginning “Lug width is the essential one: the inside distance between…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Document spring-bar diameter, end-tip fit and the strap’s clearance using appropriate measuring tools. If dimensions or compatibility are uncertain, ask a watchmaker rather than forcing a bar or substituting an unsuitable part.
Case 26 — Maintenance question: how do I tell if an automatic actually needs service?
If the manufacturer provides a suitable procedure, a running-time log can support a service enquiry. State the winding method and stop time. A shortened run does not identify the cause by itself.