Case 22 — Strap dimensions: lug width, taper, thickness and spring bar diameter explained
Document spring-bar diameter, end-tip fit and the strap’s clearance using appropriate measuring tools. If dimensions or compatibility are uncertain, ask a watchmaker rather than forcing a bar or substituting an unsuitable part.
Check whether a compatible half-link exists for the exact bracelet reference. Compatibility involves the connection and hardware, not just width. Ask a watchmaker if the correct part is uncertain.
Case 4 — Crystal reflections: why a dark patch is not a coating test
No single lighting setup settles that question. Compare multiple controlled angles and describe the visible observation without asserting material specifications that have not been verified.
Clarification for “First QC request: the minimum useful information”: the point beginning “State the model configuration, the specific concern and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 6 — Strap compatibility: width is only the first measurement
Correction note for “Strap compatibility: width is only the first measurement”: retain the wording beginning “Measure the lug opening and document bar diameter,…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 12 — Magnetism and rate: record evidence before naming a cause
Record the change and the circumstances without treating the suspected cause as established. A competent watchmaker can test and diagnose it; random adjustment is not a substitute for assessment.
Case 9 — Shipping timeline: separate dispatch, handover and scan events
Summary draft for “Shipping timeline: separate dispatch, handover and scan events”: the answer addresses “Distinguish label creation from physical acceptance and retain dated…”; the related point is “Ask the sender or carrier for clarification; missing scans alone…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Case 6 — Comparing dial colour under different lighting
State the lighting and white-balance limitations. Compare controlled images where available and avoid calling a colour defect from differently processed photographs.
Case 34 — Beginner glossary Q&A: complication, caliber, jewel count, power reserve
New here and reading spec sheets for the first time. Four terms keep tripping me up: complication, caliber, jewel count and power reserve. Short definitions would help, and so would a note on which ones actually matter when comparing two everyday watches.
Exercise RWF-26465/34: address this question within its stated limits.
Case 9 — Comparing versions without mixing case sizes
Two purported versions differ in case diameter and bracelet. How can the comparison avoid attributing every difference to a revision?
Exercise RWF-23960/9: address this question within its stated limits.
Case 16 — Movement identification: the limits of a rotor photograph
Clarification for “Movement identification: the limits of a rotor photograph”: the point beginning “Describe visible bridge shapes and markings separately…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Summary draft for “Case finishing: distinguish a reflection from a surface mark”: the answer addresses “Ask for photographs with the light moved and…”; the related point is “A mark should be assessed across multiple views; aggressive polishing…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Case 18 — Strap dimensions: lug width, taper, thickness and spring bar diameter explained
Summary order of importance. 1) Lug width, measured between the lugs. 2) Lug-end thickness against clearance. 3) Spring bar diameter. 4) Taper and buckle width. 5) Length, which is usually given as long side / short side in mm and should be compared with a strap that already fits you.
Case 32 — Date window centring: compare the same date at the same angle
Different numerals have different optical centres. A comparison mixes two dates and unequal magnification. How can the evidence be improved?
Exercise RWF-19101/32: address this question within its stated limits.
Ask for a straight-on dial photo with diffuse light and no flash, the full dial in frame, and the hands placed away from the indices (10:10 isn't ideal, because it covers the upper markers). Flash flattens printing and hides lume condition. Diffuse light shows print edges, alignment and any spotting.