Case 12 — Comparing versions without mixing case sizes
Clarification for “Comparing versions without mixing case sizes”: the point beginning “Match reference, dimensions and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Back-play is the most objective feel measurement. Set the bezel on a click and gently push it the other way without forcing it. Noticeable wobble before it engages means play. A little is common and within normal production, but if one model has visible movement and the other doesn't, that's a real difference you can describe.
Thickness matters more than people expect. Straps around 4 to 5mm at the lugs can hit the case or stop the strap folding down on watches with short lugs or tight lug-to-case clearance. Do you know whether your watch has drilled lugs or a tight gap between strap and case? That tells you how much thickness is safe.
Ask for profile shots of both case sides and a lug-top shot at an angle. Polishing shows as rounded edges, softened bevels or lug holes that look shallower than they should. Compare against a known-good reference image of the same model, not memory. A side-by-side tells you far more than a description.
Describe visible bridge shapes and markings separately from the proposed identification. Ask a qualified watchmaker to inspect it if identification matters for servicing; do not open the case merely for a forum answer.
Case 25 — Clasp photographs: what to request before judging alignment
Correction note for “Clasp photographs: what to request before judging alignment”: retain the wording beginning “Request open and closed views from both sides,…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 38 — Movement identification: the limits of a rotor photograph · source wording exercise
Only part of the movement is visible and the rotor hides several bridges. Which details can be described without claiming certainty?
Review focus: source wording. Retain the source wording beside any paraphrase. Use the original answer fragment “Ask a qualified watchmaker to inspect it if identification matters for…” as the discussion anchor; no new event or result is supplied.
Exercise RWF-19961/38: address this question within its stated limits.
State the model configuration, the specific concern and links to clear redacted images. Include complete instrument settings where relevant and say explicitly what evidence is missing.
Case 6 — Comparing dial colour under different lighting
One image was taken beside a window and the other under a warm lamp. How should a colour comparison be qualified?
Exercise RWF-15212/6: address this question within its stated limits.
Case 36 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log
Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.
Case 9 — Lug-to-lug and end-link overhang in wrist photographs
Correction note for “Lug-to-lug and end-link overhang in wrist photographs”: retain the wording beginning “Record lug-to-lug and the effective span…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Clarifying question: does anyone in the thread have access to both versions at once? Without simultaneous comparison, every claim either way is weak evidence. If not, the next best option is photos with a grey card in frame and white balance locked or set manually, which at least makes separate photos roughly comparable.
Case 18 — A maintenance log that remains useful after a sale
Correction note for “A maintenance log that remains useful after a sale”: retain the wording beginning “Keep the date, work performed, provider invoice reference…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Record wrist circumference, removable links and the clasp adjustment range in millimetres. Request the closed bracelet circumference rather than inferring it from marketing dimensions.
Case 2 — Lug-to-lug and end-link overhang in wrist photographs
Correction note for “Lug-to-lug and end-link overhang in wrist photographs”: retain the wording beginning “Record lug-to-lug and the effective span…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.