Case 9 — Comparing dial colour under different lighting
Correction note for “Comparing dial colour under different lighting”: retain the wording beginning “State the lighting and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Sealing and movement performance are separate questions. Ask a qualified watchmaker about inspection and testing appropriate to the particular watch and its intended use; a healthy rate does not establish water resistance.
Thickness matters more than people expect. Straps around 4 to 5mm at the lugs can hit the case or stop the strap folding down on watches with short lugs or tight lug-to-case clearance. Do you know whether your watch has drilled lugs or a tight gap between strap and case? That tells you how much thickness is safe.
Case 44 — Movement identification: the limits of a rotor photograph · source wording exercise
Correction note for “Movement identification: the limits of a rotor photograph”: retain the wording beginning “Ask a qualified watchmaker to inspect it if identification matters for…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Retain the source wording beside any paraphrase.
Case 22 — Case finishing: distinguish a reflection from a surface mark
Correction note for “Case finishing: distinguish a reflection from a surface mark”: retain the wording beginning “Ask for photographs with the light moved and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 35 — Bracelet fit: measuring the usable clasp adjustment
A nominal case diameter says little about a bracelet that cannot be shortened enough. How should a sizing question be documented?
Exercise RWF-19961/35: address this question within its stated limits.
Clarification for “Magnetism and rate: record evidence before naming a cause”: the point beginning “Record the change and the circumstances without treating…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Method note for “Lug-to-lug and end-link overhang in wrist photographs”: use “Record lug-to-lug and the effective span…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Case 3 — Lume comparison: keep exposure and charging conditions consistent
Two glowing dials are shown with different camera exposure and unknown charging time. What can the images establish?
Exercise RWF-15212/3: address this question within its stated limits.
Case 33 — Crystal reflections: why a dark patch is not a coating test
No single lighting setup settles that question. Compare multiple controlled angles and describe the visible observation without asserting material specifications that have not been verified.
Case 6 — What a water-resistance claim does and does not establish
Correction note for “What a water-resistance claim does and does not establish”: retain the wording beginning “Ask a qualified watchmaker about a suitable test for that individual…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 15 — QC checklist: prioritise observable faults over pixel hunting
Correction note for “QC checklist: prioritise observable faults over pixel hunting”: retain the wording beginning “Start with function, legibility, assembly and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Regulation is possible if you want it closer. On many movements it's a quick adjustment by a watchmaker. Can you check whether the losing rate is consistent or getting worse? A stable -8 is a good candidate for simple regulation. A growing loss points to something else, such as falling amplitude, and regulation alone won't fix that.
Use the same numeral, camera axis and approximate image scale. Keep the uncropped originals alongside the detail crops and distinguish optical balance from physical window alignment.
Micro-adjust spacing varies by clasp. Measure the actual change at each setting rather than assuming a standard number of millimetres; compare the usable range with the link length.