Case 10 — Comparing versions without mixing case sizes
Two purported versions differ in case diameter and bracelet. How can the comparison avoid attributing every difference to a revision?
Exercise RWF-31231/10: address this question within its stated limits.
Case 3 — Seller review template: facts, dates and unresolved questions
Correction note for “Seller review template: facts, dates and unresolved questions”: retain the wording beginning “Use fields for order date, promised terms, dated…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Method note for “First QC request: the minimum useful information”: use “State the model configuration, the specific concern and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Describe whether resistance occurs during winding or setting and whether the crown engages consistently. Stop forcing it and arrange inspection rather than trying an unverified repair from a thread.
Case 21 — Crystal types: sapphire, mineral and acrylic trade-offs for daily wear
Summary. Pick sapphire for scratch resistance in low-impact use, acrylic for impact tolerance and easy polishing, and mineral as a low-cost middle option. Prefer inner-surface AR if you're worried about wear. Look at crystal profile when comparing thickness. Choose by how you'll use the watch, not by the material label.
Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.
Limit of the answer in “Timegrapher reading context: what do rate, amplitude and beat error actually tell me?”: “First identify the caliber, lift-angle setting, winding…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.
Case 31 — Date window centring: compare the same date at the same angle
Limit of the answer in “Date window centring: compare the same date at the same angle”: “Use the same numeral, camera axis…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.
Case 3 — Comparing versions without mixing case sizes
Method note for “Comparing versions without mixing case sizes”: use “Match reference, dimensions and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Clarification for “QC checklist: prioritise observable faults over pixel hunting”: the point beginning “Explain what the full-size image shows, what the crop adds and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 39 — Maintenance question: how do I tell if an automatic actually needs service? · source wording exercise
Common advice says service every five years, but service is expensive and some people run watches much longer. What observable signs actually indicate a mechanical watch needs attention, as opposed to just being due on a calendar?
Review focus: source wording. Retain the source wording beside any paraphrase. Use the original answer fragment “Useful signs, in rough order of seriousness: power reserve noticeably shorter…” as the discussion anchor; no new event or result is supplied.
Exercise RWF-18903/39: address this question within its stated limits.
Method note for “Date window centring: compare the same date at the same angle”: use “Use the same numeral, camera axis…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Case 14 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log
State whether thickness includes the highest point of a domed crystal. Different measurement methods can produce different figures, so keep both the source and method beside each dimension.
Case 23 — Comparing versions without mixing case sizes
Summary draft for “Comparing versions without mixing case sizes”: the answer addresses “Match reference, dimensions and…”; the related point is “List confirmed differences separately from seller descriptions and date the comparison…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Case 3 — Crystal reflections: why a dark patch is not a coating test
Limit of the answer in “Crystal reflections: why a dark patch is not a coating test”: “No single lighting setup settles…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.