Case 23 — Clasp photographs: what to request before judging alignment
The available image hides the hinge and only shows the outer surface. Which additional views would answer the question?
Exercise RWF-29888/23: address this question within its stated limits.
Case 37 — QC photography: what photos actually help verify a pre-owned listing? · source wording exercise
When asking a seller for extra photos of a pre-owned watch, what shots are actually useful as evidence? Listings tend to have glossy angled photos that hide more than they show. I'd like a standard request list the forum can reuse.
Review focus: source wording. Retain the source wording beside any paraphrase. Use the original answer fragment “Flash flattens printing and hides…” as the discussion anchor; no new event or result is supplied.
Exercise RWF-29092/37: address this question within its stated limits.
Case 112 — Strap compatibility: width is only the first measurement · documentation exercise
Limit of the answer in “Strap compatibility: width is only the first measurement”: “Avoid forcing an assembly that does not fit and…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: documentation. Distinguish an original record from a proposed record format.
Case 2 — First QC request: the minimum useful information
What should an initial QC request include so replies can address the actual question?
Exercise RWF-27179/2: address this question within its stated limits.
Case 12 — Lume questions: why does my lume fade so quickly, and how should I compare it?
Clarifying question: how are you charging it? A few seconds under a warm indoor bulb gives a much weaker charge than daylight or a UV source. Many 'weak lume' reports turn out to be undercharging. Try a consistent charge, such as 30 seconds under a phone flashlight at a fixed distance, before judging.
Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.
Case 4 — Strap dimensions: lug width, taper, thickness and spring bar diameter explained
Thickness matters more than people expect. Straps around 4 to 5mm at the lugs can hit the case or stop the strap folding down on watches with short lugs or tight lug-to-case clearance. Do you know whether your watch has drilled lugs or a tight gap between strap and case? That tells you how much thickness is safe.
Case 29 — Service enquiry: information a watchmaker can use
Limit of the answer in “Service enquiry: information a watchmaker can use”: “Document when it stops, winding behaviour, recent impacts and…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.
Case 30 — QC checklist: prioritise observable faults over pixel hunting
Summary draft for “QC checklist: prioritise observable faults over pixel hunting”: the answer addresses “Start with function, legibility, assembly and…”; the related point is “Explain what the full-size image shows, what the crop adds and…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Describe whether resistance occurs during winding or setting and whether the crown engages consistently. Stop forcing it and arrange inspection rather than trying an unverified repair from a thread.
Case 28 — Beginner glossary Q&A: complication, caliber, jewel count, power reserve
Power reserve is how long the watch runs from full wind until it stops. It matters if you rotate watches: a 38-hour reserve may stop over a weekend off the wrist, while 70-plus hours may not. One clarifying point is that rate stability often gets worse near the end of the reserve, so the full figure is not all precision-grade running time.
Case 7 — Date window centring: compare the same date at the same angle
Correction note for “Date window centring: compare the same date at the same angle”: retain the wording beginning “Use the same numeral, camera axis…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Clarification for “Packing photographs: document condition without exposing an address”: the point beginning “Photograph the item and protective packing…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 15 — Accuracy expectations: is -8 s/d acceptable on an entry-level automatic?
A correction to a common belief: an automatic doesn't need to match a quartz watch to be healthy. Consistency matters more than the absolute figure. A watch that's reliably -8 every day is easy to live with, since you correct it once a week. One that swings from +10 to -15 is the real concern.
Ask a qualified watchmaker about a suitable test for that individual case and record the test date and method. A photograph or a caseback engraving is not proof of water resistance.