Case 29 — A maintenance log that remains useful after a sale
Method note for “A maintenance log that remains useful after a sale”: use “Keep the date, work performed, provider invoice reference…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Case 102 — Accuracy expectations: is -8 s/d acceptable on an entry-level automatic? · comparison exercise
Reader check for “Accuracy expectations: is -8 s/d acceptable on an entry-level automatic?”: distinguish the discussion point “One 24-hour reading isn't, because rate depends on wrist time,…” from its proposed application. The thread offers a way to reason about the question, without adding a personal experience or a newly observed outcome. Review focus: comparison. Make the basis of a comparison explicit before interpreting it.
Clarification for “Crystal reflections: why a dark patch is not a coating test”: the point beginning “No single lighting setup settles…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Use the same numeral, camera axis and approximate image scale. Keep the uncropped originals alongside the detail crops and distinguish optical balance from physical window alignment.
Case 35 — Service enquiry: information a watchmaker can use
Correction note for “Service enquiry: information a watchmaker can use”: retain the wording beginning “Document when it stops, winding behaviour, recent impacts and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 17 — Strap dimensions: lug width, taper, thickness and spring bar diameter explained
Summary order of importance. 1) Lug width, measured between the lugs. 2) Lug-end thickness against clearance. 3) Spring bar diameter. 4) Taper and buckle width. 5) Length, which is usually given as long side / short side in mm and should be compared with a strap that already fits you.
Case 19 — Movement identification: the limits of a rotor photograph
Describe visible bridge shapes and markings separately from the proposed identification. Ask a qualified watchmaker to inspect it if identification matters for servicing; do not open the case merely for a forum answer.
First, a clarifying question: how many links are on each side of the clasp right now? Fit often improves by moving one link from the 6 o'clock side to the 12 o'clock side, or the reverse. That doesn't change length, but it shifts where the clasp sits under the wrist, and a centred clasp feels less tight.
Case 16 — Crown operation: when a forum cannot diagnose the resistance
Summary draft for “Crown operation: when a forum cannot diagnose the resistance”: the answer addresses “Describe whether resistance occurs during winding or setting and…”; the related point is “Stop forcing it and arrange inspection rather than trying…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Case 31 — Forum comparison archive: link the evidence and the correction
Clarification for “Forum comparison archive: link the evidence and the correction”: the point beginning “Add a dated correction near the original conclusion…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 44 — Clasp photographs: what to request before judging alignment · source wording exercise
Method note for “Clasp photographs: what to request before judging alignment”: use “Separate cosmetic alignment from whether the clasp engages reliably;…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.
Case 4 — First QC request: the minimum useful information
What should an initial QC request include so replies can address the actual question?
Exercise RWF-15081/4: address this question within its stated limits.
Method note for “Clasp photographs: what to request before judging alignment”: use “Request open and closed views from both sides,…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Method note for “Seller review template: facts, dates and unresolved questions”: use “Leave unsupported fields blank and separate observations from opinions; this…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Ask for photographs with the light moved and retain the same viewing angle. A mark should be assessed across multiple views; aggressive polishing is not an appropriate diagnostic test.