Case 280 — Crystal types: sapphire, mineral and acrylic trade-offs for daily wear · reader check exercise
Spec sheets list sapphire, mineral or acrylic crystals, and opinions in threads are very strong. For a daily-wear watch, what are the real trade-offs, and is an anti-reflective coating worth paying for?
Review focus: reader check. State what a new reader can and cannot infer from this exercise. Use the original answer fragment “For work with frequent knocks, a slightly domed acrylic that you…” as the discussion anchor; no new event or result is supplied.
Exercise RWF-25905/280: address this question within its stated limits.
Clarification for “Comparing dial colour under different lighting”: the point beginning “State the lighting and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 23 — Strap dimensions: lug width, taper, thickness and spring bar diameter explained
Lug width is the essential one: the inside distance between the lugs where the strap fits. Measure with a ruler marked in millimetres, ideally reading it under magnification. Most watches use even numbers (18, 20, 22mm), but odd widths exist. If you measure 19 or 21, measure again and check the manufacturer spec before ordering.
Case 5 — Magnetism and rate: record evidence before naming a cause
Clarification for “Magnetism and rate: record evidence before naming a cause”: the point beginning “Record the change and the circumstances without treating…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 6 — Maintenance question: how do I tell if an automatic actually needs service?
A sudden rate change has several possible causes. Ask a watchmaker to test suspected magnetism rather than diagnosing it from a compass or attempting an adjustment based on forum replies.
Case 44 — Model comparison: dive bezel action and alignment, how to compare fairly · source wording exercise
Method note for “Model comparison: dive bezel action and alignment, how to compare fairly”: use “Crisp vs mushy is mostly about…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.
Case 4 — Reading a timegrapher recording without losing the context
Clarification for “Reading a timegrapher recording without losing the context”: the point beginning “Keep the complete recording and ask for the…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 18 — Lume comparison: keep exposure and charging conditions consistent
Correction note for “Lume comparison: keep exposure and charging conditions consistent”: retain the wording beginning “Treat the comparison…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 31 — What a water-resistance claim does and does not establish
Correction note for “What a water-resistance claim does and does not establish”: retain the wording beginning “Ask a qualified watchmaker about a suitable test for that individual…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
On alignment, a clarifying point: is the misalignment visible straight on, or only from an angle? Parallax on a raised bezel can make a perfectly aligned pip look half a click off when viewed slightly from the side. Photograph straight above the dial before calling it misaligned.
Case 43 — Strap compatibility: width is only the first measurement · source wording exercise
Summary draft for “Strap compatibility: width is only the first measurement”: the answer addresses “Avoid forcing an assembly that does not fit and…”; the related point is “Measure the lug opening and document bar diameter,…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: source wording. Retain the source wording beside any paraphrase.
Sealing and movement performance are separate questions. Ask a qualified watchmaker about inspection and testing appropriate to the particular watch and its intended use; a healthy rate does not establish water resistance.
Start with function, legibility, assembly and clear visible damage. Explain what the full-size image shows, what the crop adds and what remains uncertain; do not turn an overlay into an automatic verdict.
Correction note for “First QC request: the minimum useful information”: retain the wording beginning “State the model configuration, the specific concern and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Method note for “Packing photographs: document condition without exposing an address”: use “Photograph the item and protective packing…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.