Skip to content
RepWatchForumSign in

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 23 total)

Case 17 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log

I'm putting together a side-by-side of the 38mm and 40mm versions of a common three-hand field watch design. The aim is a reference post we can fix over time instead of repeating the same arguments. Corrections go in a dated log at the bottom. What should the table include besides case diameter, and which specs are usually misreported?

Exercise RWF-29865/17: address this question within its stated limits.

Case 14 — Crown operation: when a forum cannot diagnose the resistance

Correction note for “Crown operation: when a forum cannot diagnose the resistance”: retain the wording beginning “Describe whether resistance occurs during winding or setting and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.

Case 19 — First QC request: the minimum useful information

What should an initial QC request include so replies can address the actual question?

Exercise RWF-28278/19: address this question within its stated limits.

Case 8 — Crown operation: when a forum cannot diagnose the resistance

Describe whether resistance occurs during winding or setting and whether the crown engages consistently. Stop forcing it and arrange inspection rather than trying an unverified repair from a thread.

Case 198 — Beginner glossary Q&A: complication, caliber, jewel count, power reserve · correction exercise

Correction note for “Beginner glossary Q&A: complication, caliber, jewel count, power reserve”: retain the wording beginning “A date window counts, technically, and so do a…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Preserve the old wording if a later source changes the interpretation.

Correction note for “Crown operation: when a forum cannot diagnose the resistance”: retain the wording beginning “Stop forcing it and arrange inspection rather than trying…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.

Case 12 — Timegrapher reading context: what do rate, amplitude and beat error actually tell me?

Can the same settings and winding state be used for several positions? Record each position separately rather than combining measurements taken under different conditions.

Case 15 — Disputed observation: is this dial colour shift real or just lighting?

Suggested protocol. 1) Both dials in one frame. 2) Diffuse daylight, no direct sun, plus a second shot under neutral indoor light. 3) Grey card visible. 4) No filters, no editing. 5) State camera settings if known. If both shots show the same direction of difference, the claim is supported. If the difference flips between lighting conditions, it's most likely lighting.

Case 34 — Maintenance question: how do I tell if an automatic actually needs service?

Common advice says service every five years, but service is expensive and some people run watches much longer. What observable signs actually indicate a mechanical watch needs attention, as opposed to just being due on a calendar?

Exercise RWF-20816/34: address this question within its stated limits.

Start with how you measured it. Comparing against a phone clock once a day for a week, at the same time, and noting the offset is reliable enough. One 24-hour reading isn't, because rate depends on wrist time, position overnight and state of wind. Average across several days before deciding anything.

Case 20 — Strap dimensions: lug width, taper, thickness and spring bar diameter explained

Thickness matters more than people expect. Straps around 4 to 5mm at the lugs can hit the case or stop the strap folding down on watches with short lugs or tight lug-to-case clearance. Do you know whether your watch has drilled lugs or a tight gap between strap and case? That tells you how much thickness is safe.

Case 2 — Disputed observation: is this dial colour shift real or just lighting?

Batch variation on coloured dials does happen in general. Plating, lacquer thickness and supplier changes can all shift tone, so the claim isn't implausible. Plausible isn't the same as confirmed, though. The thread should keep 'possible' and 'shown' as separate statuses rather than letting repetition turn a hypothesis into accepted fact.

Case 22 — Comparing dial colour under different lighting

Method note for “Comparing dial colour under different lighting”: use “State the lighting and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.

Case 7 — What a water-resistance claim does and does not establish

Summary draft for “What a water-resistance claim does and does not establish”: the answer addresses “Ask a qualified watchmaker about a suitable test for that individual…”; the related point is “A photograph or a caseback engraving is not…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.

A bright initial glow followed by a steep drop is normal for photoluminescent pigments. Afterglow fades fastest in the first minutes and then settles to a dim, long-lasting level that dark-adapted eyes can still read. The real question is whether it's readable after an hour in darkness, not how it looks right after charging.

Viewing 15 posts - 1 through 15 (of 23 total)