Case 20 — First QC request: the minimum useful information
Method note for “First QC request: the minimum useful information”: use “State the model configuration, the specific concern and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Case 30 — Strap dimensions: lug width, taper, thickness and spring bar diameter explained
Summary order of importance. 1) Lug width, measured between the lugs. 2) Lug-end thickness against clearance. 3) Spring bar diameter. 4) Taper and buckle width. 5) Length, which is usually given as long side / short side in mm and should be compared with a strap that already fits you.
Case 38 — Beginner glossary Q&A: complication, caliber, jewel count, power reserve · source wording exercise
Method note for “Beginner glossary Q&A: complication, caliber, jewel count, power reserve”: use “Two watches from different brands can share the same caliber…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.
Case 10 — Reading a timegrapher recording without losing the context
Keep the complete recording and ask for the settings, winding state and position. A single number cannot establish service condition, movement identity or performance on a wrist.
Limit of the answer in “Comparing versions without mixing case sizes”: “Match reference, dimensions and…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.
Jewel count describes bearings used in a movement design; it is not a quality ranking. Compare the documented movement architecture and service support rather than assuming a higher count makes one watch better.
Case 20 — QC photography: what photos actually help verify a pre-owned listing?
Ask for profile shots of both case sides and a lug-top shot at an angle. Polishing shows as rounded edges, softened bevels or lug holes that look shallower than they should. Compare against a known-good reference image of the same model, not memory. A side-by-side tells you far more than a description.
Micro-adjust spacing varies by clasp. Measure the actual change at each setting rather than assuming a standard number of millimetres; compare the usable range with the link length.
Clarification for “Shipping timeline: separate dispatch, handover and scan events”: the point beginning “Distinguish label creation from physical acceptance and retain dated…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 9 — Packing photographs: document condition without exposing an address
Correction note for “Packing photographs: document condition without exposing an address”: retain the wording beginning “Photograph the item and protective packing…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 11 — Beginner glossary Q&A: complication, caliber, jewel count, power reserve
For a two-watch comparison, the practical order is usually case dimensions first, then power reserve if you rotate, then caliber for serviceability. Jewel count comes last. Complications only matter if you'll use them. Can you say what the two candidates are, in generic terms like 'dive style vs dress style'? The priorities shift a lot between those.
Case 37 — Reading a timegrapher recording without losing the context · source wording exercise
Method note for “Reading a timegrapher recording without losing the context”: use “A single number cannot establish service condition, movement identity…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.
Method note for “QC checklist: prioritise observable faults over pixel hunting”: use “Explain what the full-size image shows, what the crop adds and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Case 27 — Accuracy expectations: is -8 s/d acceptable on an entry-level automatic?
Log the rate over several comparable days, identify the correct specification and state the conditions. Stable and changing patterns raise different questions; a watchmaker can assess whether regulation, inspection or no action is appropriate.
Document when it stops, winding behaviour, recent impacts and the positions in which it happens. Be honest about the watch and request an assessment before approving work or ordering parts.