Skip to content
RepWatchForumSign in

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 23 total)

Case 24 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log

Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.

Case 27 — Case finishing: distinguish a reflection from a surface mark

Clarification for “Case finishing: distinguish a reflection from a surface mark”: the point beginning “Ask for photographs with the light moved and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.

Photograph the item and protective packing separately from the label. Remove names, addresses, barcodes and tracking tokens from public images while keeping originals privately.

Case 40 — Bracelet fit: measuring the usable clasp adjustment · source wording exercise

A nominal case diameter says little about a bracelet that cannot be shortened enough. How should a sizing question be documented?

Review focus: source wording. Retain the source wording beside any paraphrase. Use the original answer fragment “Request the closed bracelet circumference rather than inferring…” as the discussion anchor; no new event or result is supplied.

Exercise RWF-28092/40: address this question within its stated limits.

Case 42 — Accuracy expectations: is -8 s/d acceptable on an entry-level automatic? · source wording exercise

Correction note for “Accuracy expectations: is -8 s/d acceptable on an entry-level automatic?”: retain the wording beginning “Comparing against a phone clock once a day for a week,…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Retain the source wording beside any paraphrase.

Case 44 — Lug-to-lug and end-link overhang in wrist photographs · source wording exercise

A wide-angle wrist photo exaggerates the nearest edge of the case. How can two watches be compared fairly?

Review focus: source wording. Retain the source wording beside any paraphrase. Use the original answer fragment “Use a similar camera distance and neutral wrist position; photographs support…” as the discussion anchor; no new event or result is supplied.

Exercise RWF-25897/44: address this question within its stated limits.

Case 22 — What a water-resistance claim does and does not establish

Summary draft for “What a water-resistance claim does and does not establish”: the answer addresses “Ask a qualified watchmaker about a suitable test for that individual…”; the related point is “A photograph or a caseback engraving is not…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.

The difficulty is that phone cameras adjust white balance automatically, and blue dials are especially sensitive. Two photos of the same dial under different light can easily look like a 'batch difference'. Any comparison needs both dials in the same frame, under the same light, ideally next to a neutral grey or white reference card.

Correction note for “Bracelet fit: measuring the usable clasp adjustment”: retain the wording beginning “Record wrist circumference, removable links and the clasp…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.

Case 8 — Strap compatibility: width is only the first measurement

Clarification for “Strap compatibility: width is only the first measurement”: the point beginning “Measure the lug opening and document bar diameter,…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.

Limit of the answer in “Date window centring: compare the same date at the same angle”: “Use the same numeral, camera axis…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.

Case 9 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log

State whether thickness includes the highest point of a domed crystal. Different measurement methods can produce different figures, so keep both the source and method beside each dimension.

State whether thickness includes the highest point of a domed crystal. Different measurement methods can produce different figures, so keep both the source and method beside each dimension.

Case 25 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log

State whether thickness includes the highest point of a domed crystal. Different measurement methods can produce different figures, so keep both the source and method beside each dimension.

Method note for “Magnetism and rate: record evidence before naming a cause”: use “Record the change and the circumstances without treating…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.

Viewing 15 posts - 1 through 15 (of 23 total)