Case 8 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log
Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.
Case 36 — Packing photographs: document condition without exposing an address
Correction note for “Packing photographs: document condition without exposing an address”: retain the wording beginning “Photograph the item and protective packing…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 14 — Crystal types: sapphire, mineral and acrylic trade-offs for daily wear
Summary. Pick sapphire for scratch resistance in low-impact use, acrylic for impact tolerance and easy polishing, and mineral as a low-cost middle option. Prefer inner-surface AR if you're worried about wear. Look at crystal profile when comparing thickness. Choose by how you'll use the watch, not by the material label.
Case 19 — Service enquiry: information a watchmaker can use
Method note for “Service enquiry: information a watchmaker can use”: use “Document when it stops, winding behaviour, recent impacts and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Document when it stops, winding behaviour, recent impacts and the positions in which it happens. Be honest about the watch and request an assessment before approving work or ordering parts.
A notation like 20/16 means 20mm at the lugs, tapering to 16mm at the buckle. Taper affects look and comfort more than fit. A strong taper suits smaller and dressier cases, a straight strap suits sport watches. Your buckle or clasp also has to match the narrow end, so check that if you want to reuse an existing buckle.
Clarification for “Crown operation: when a forum cannot diagnose the resistance”: the point beginning “Describe whether resistance occurs during winding or setting and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Thickness matters more than people expect. Straps around 4 to 5mm at the lugs can hit the case or stop the strap folding down on watches with short lugs or tight lug-to-case clearance. Do you know whether your watch has drilled lugs or a tight gap between strap and case? That tells you how much thickness is safe.
Clarification for “Lume comparison: keep exposure and charging conditions consistent”: the point beginning “Treat the comparison…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 18 — Case finishing: distinguish a reflection from a surface mark
Correction note for “Case finishing: distinguish a reflection from a surface mark”: retain the wording beginning “Ask for photographs with the light moved and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 1 — A maintenance log that remains useful after a sale
Keep the date, work performed, provider invoice reference and test results where available. Redact addresses and payment information; do not invent service events to fill an empty history.
Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.
Case 24 — Bracelet fit: measuring the usable clasp adjustment
Correction note for “Bracelet fit: measuring the usable clasp adjustment”: retain the wording beginning “Record wrist circumference, removable links and the clasp…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Case 2 — Model comparison: dive bezel action and alignment, how to compare fairly
Separate preference from a potential functional problem. Inconsistent engagement, slipping or uncertain alignment should be documented and checked against the design’s specification by a competent watchmaker; do not invent a universal defect threshold.
Record lug-to-lug and the effective span including rigid end links. Use a similar camera distance and neutral wrist position; photographs support fit discussion but do not replace measurements.