Skip to content
RepWatchForumSign in

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 22 total)
ClaspCheck 01556Participant

Case 12 — Case finishing: distinguish a reflection from a surface mark

Method note for “Case finishing: distinguish a reflection from a surface mark”: use “Ask for photographs with the light moved and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.

ClaspCheck 01556Participant

Method note for “A maintenance log that remains useful after a sale”: use “Keep the date, work performed, provider invoice reference…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.

ClaspCheck 01556Participant

Lug width is the essential one: the inside distance between the lugs where the strap fits. Measure with a ruler marked in millimetres, ideally reading it under magnification. Most watches use even numbers (18, 20, 22mm), but odd widths exist. If you measure 19 or 21, measure again and check the manufacturer spec before ordering.

ClaspCheck 01556Participant

Case 10 — Comparing dial colour under different lighting

Clarification for “Comparing dial colour under different lighting”: the point beginning “State the lighting and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.

ClaspCheck 01556Participant

Case 3 — Bracelet fit: measuring the usable clasp adjustment

A nominal case diameter says little about a bracelet that cannot be shortened enough. How should a sizing question be documented?

Exercise RWF-24205/3: address this question within its stated limits.

ClaspCheck 01556Participant

Suggested protocol. 1) Both dials in one frame. 2) Diffuse daylight, no direct sun, plus a second shot under neutral indoor light. 3) Grey card visible. 4) No filters, no editing. 5) State camera settings if known. If both shots show the same direction of difference, the claim is supported. If the difference flips between lighting conditions, it's most likely lighting.

ClaspCheck 01556Participant

Clarification for “Service enquiry: information a watchmaker can use”: the point beginning “Document when it stops, winding behaviour, recent impacts and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.

ClaspCheck 01556Participant

Summary draft for “Timegrapher reading context: what do rate, amplitude and beat error actually tell me?”: the answer addresses “First identify the caliber, lift-angle setting, winding…”; the related point is “Without those fields, the rate, amplitude and beat-error values lack…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.

ClaspCheck 01556Participant

Case 35 — Reading a timegrapher recording without losing the context

The supplied screen shows a rate but does not identify the lift angle, position or winding state. Which observations should accompany the recording?

Exercise RWF-19240/35: address this question within its stated limits.

ClaspCheck 01556Participant

Lug width is the essential one: the inside distance between the lugs where the strap fits. Measure with a ruler marked in millimetres, ideally reading it under magnification. Most watches use even numbers (18, 20, 22mm), but odd widths exist. If you measure 19 or 21, measure again and check the manufacturer spec before ordering.

ClaspCheck 01556Participant

Clarifying question for the thread: is the goal to check authenticity, condition, or both? For condition, the request list above is enough. For authenticity, you also need caseback, serial or reference engravings, and ideally movement photos. Movement photos usually require opening the watch, which a seller may reasonably refuse without a watchmaker present.

ClaspCheck 01556Participant

Case 39 — Packing photographs: document condition without exposing an address · source wording exercise

Limit of the answer in “Packing photographs: document condition without exposing an address”: “Remove names, addresses, barcodes and tracking tokens from public…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: source wording. Retain the source wording beside any paraphrase.

ClaspCheck 01556Participant

Case 49 — Bracelet fit: measuring the usable clasp adjustment · source wording exercise

Correction note for “Bracelet fit: measuring the usable clasp adjustment”: retain the wording beginning “Request the closed bracelet circumference rather than inferring…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Retain the source wording beside any paraphrase.

ClaspCheck 01556Participant

Case 2 — Disputed observation: is this dial colour shift real or just lighting?

Batch variation on coloured dials does happen in general. Plating, lacquer thickness and supplier changes can all shift tone, so the claim isn't implausible. Plausible isn't the same as confirmed, though. The thread should keep 'possible' and 'shown' as separate statuses rather than letting repetition turn a hypothesis into accepted fact.

ClaspCheck 01556Participant

Case 3 — Seller review template: facts, dates and unresolved questions

Correction note for “Seller review template: facts, dates and unresolved questions”: retain the wording beginning “Use fields for order date, promised terms, dated…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.

Viewing 15 posts - 1 through 15 (of 22 total)