Case 16 — QC photographs: perspective or a genuinely tilted index?
A marker can look tilted when the camera is above the dial axis. What extra image would separate perspective from an assembly issue?
Exercise RWF-28618/16: address this question within its stated limits.
Case 10 — Beginner glossary Q&A: complication, caliber, jewel count, power reserve
Caliber is the movement's model designation, like a part number. Two watches from different brands can share the same caliber family with different finishing or regulation. On a spec sheet it tells you what's inside and roughly what service parts are available. It doesn't tell you how well that particular example was adjusted.
Case 28 — Timegrapher reading context: what do rate, amplitude and beat error actually tell me?
I ran a watch on a basic timegrapher and got +6 s/d, 245 degrees amplitude and 0.8 ms beat error, dial up, about an hour after winding. Is this good, bad or normal? I don't want to send it for service on a single reading.
Exercise RWF-26616/28: address this question within its stated limits.
Case 28 — Shipping timeline: separate dispatch, handover and scan events
Distinguish label creation from physical acceptance and retain dated event text with personal details removed. Ask the sender or carrier for clarification; missing scans alone do not establish loss or seizure.
Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.
Micro-adjust spacing varies by clasp. Measure the actual change at each setting rather than assuming a standard number of millimetres; compare the usable range with the link length.
Case 16 — Beginner glossary Q&A: complication, caliber, jewel count, power reserve
Caliber is the movement's model designation, like a part number. Two watches from different brands can share the same caliber family with different finishing or regulation. On a spec sheet it tells you what's inside and roughly what service parts are available. It doesn't tell you how well that particular example was adjusted.
Clarification for “Clasp photographs: what to request before judging alignment”: the point beginning “Request open and closed views from both sides,…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Method note for “What a water-resistance claim does and does not establish”: use “A photograph or a caseback engraving is not…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Clarification for “Lume comparison: keep exposure and charging conditions consistent”: the point beginning “Treat the comparison…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Distinguish label creation from physical acceptance and retain dated event text with personal details removed. Ask the sender or carrier for clarification; missing scans alone do not establish loss or seizure.
Case 30 — Case finishing: distinguish a reflection from a surface mark
Method note for “Case finishing: distinguish a reflection from a surface mark”: use “Ask for photographs with the light moved and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Method note for “QC checklist: prioritise observable faults over pixel hunting”: use “Start with function, legibility, assembly and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Case 9 — Timegrapher reading context: what do rate, amplitude and beat error actually tell me?
A useful table has columns for date, position, winding state, lift angle, rate, amplitude and beat error. Keep the full recording so settings and stability can be checked.
Correction note for “Service enquiry: information a watchmaker can use”: retain the wording beginning “Document when it stops, winding behaviour, recent impacts and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.