Case 83 — Comparing dial colour under different lighting · comparison exercise
Method note for “Comparing dial colour under different lighting”: use “State the lighting and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Make the basis of a comparison explicit before interpreting it.
Describe visible bridge shapes and markings separately from the proposed identification. Ask a qualified watchmaker to inspect it if identification matters for servicing; do not open the case merely for a forum answer.
Case 7 — Magnetism and rate: record evidence before naming a cause
Method note for “Magnetism and rate: record evidence before naming a cause”: use “Record the change and the circumstances without treating…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.
Case 22 — Maintenance question: how do I tell if an automatic actually needs service?
A sudden rate change has several possible causes. Ask a watchmaker to test suspected magnetism rather than diagnosing it from a compass or attempting an adjustment based on forum replies.
The calendar interval is a conservative default, not a rule. Useful signs, in rough order of seriousness: power reserve noticeably shorter than spec from full wind, rate drifting outside its usual range, the watch stopping on the wrist, gritty or rough winding, and the date changing slowly or late.
Case 40 — Crystal types: sapphire, mineral and acrylic trade-offs for daily wear · source wording exercise
Limit of the answer in “Crystal types: sapphire, mineral and acrylic trade-offs for daily wear”: “Sapphire is very hard to scratch but can chip or crack…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: source wording. Retain the source wording beside any paraphrase.
Case 26 — Comparison thread: 38mm vs 40mm versions of the same field watch, with a dated correction log
Before the table goes live, a question: are you comparing current production only, or older references too? Dial printing, lume colour and crown signing often changed between batches. If older pieces are in scope, add a production-period column, or every disagreement will look like an error when it's really a running change.
Case 30 — Movement identification: the limits of a rotor photograph
Limit of the answer in “Movement identification: the limits of a rotor photograph”: “Describe visible bridge shapes and markings separately…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.
Clarification for “Reading a timegrapher recording without losing the context”: the point beginning “Keep the complete recording and ask for the…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Summary draft for “Comparing dial colour under different lighting”: the answer addresses “Compare controlled images where available and avoid calling a…”; the related point is “State the lighting and…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: scope. Keep the stated question separate from any broader claim.
Case 17 — Accuracy expectations: is -8 s/d acceptable on an entry-level automatic?
Regulation is possible if you want it closer. On many movements it's a quick adjustment by a watchmaker. Can you check whether the losing rate is consistent or getting worse? A stable -8 is a good candidate for simple regulation. A growing loss points to something else, such as falling amplitude, and regulation alone won't fix that.
Method note for “QC checklist: prioritise observable faults over pixel hunting”: use “Start with function, legibility, assembly and…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Retain the source wording beside any paraphrase.
Case 3 — Crown operation: when a forum cannot diagnose the resistance
Correction note for “Crown operation: when a forum cannot diagnose the resistance”: retain the wording beginning “Describe whether resistance occurs during winding or setting and…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Clarification for “Bracelet fit: measuring the usable clasp adjustment”: the point beginning “Record wrist circumference, removable links and the clasp…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 31 — Crystal types: sapphire, mineral and acrylic trade-offs for daily wear
On anti-reflective coatings: inner-surface AR cuts glare without wear concerns. Outer-surface AR improves legibility further but can scuff over time, and the scuffs show up as hazy patches in certain light. When comparing two watches, check which surfaces are coated. Spec sheets often just say 'AR coated' without saying where.