Case 6 — Crown operation: when a forum cannot diagnose the resistance
A description of stiffness does not establish the cause. What information is safe and useful to collect before an inspection?
Exercise RWF-29469/6: address this question within its stated limits.
Case 67 — Model comparison: dive bezel action and alignment, how to compare fairly · source wording exercise
Summary draft for “Model comparison: dive bezel action and alignment, how to compare fairly”: the answer addresses “Crisp vs mushy is mostly about…”; the related point is “Alignment can be measured, so…”. Keep both connected to the opening question, and mark any conclusion needing further records as unresolved. Review focus: source wording. Retain the source wording beside any paraphrase.
Clarification for “Service enquiry: information a watchmaker can use”: the point beginning “Document when it stops, winding behaviour, recent impacts and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
First, a clarifying question: how many links are on each side of the clasp right now? Fit often improves by moving one link from the 6 o'clock side to the 12 o'clock side, or the reverse. That doesn't change length, but it shifts where the clasp sits under the wrist, and a centred clasp feels less tight.
Case 1 — Lug-to-lug and end-link overhang in wrist photographs
Record lug-to-lug and the effective span including rigid end links. Use a similar camera distance and neutral wrist position; photographs support fit discussion but do not replace measurements.
Micro-adjust spacing varies by clasp. Measure the actual change at each setting rather than assuming a standard number of millimetres; compare the usable range with the link length.
Case 19 — Case finishing: distinguish a reflection from a surface mark
A bright line appears in one polished-case image. What additional evidence would distinguish a mark from reflected light?
Exercise RWF-20169/19: address this question within its stated limits.
Case 5 — Date window centring: compare the same date at the same angle
Different numerals have different optical centres. A comparison mixes two dates and unequal magnification. How can the evidence be improved?
Exercise RWF-19200/5: address this question within its stated limits.
Case 9 — Packing photographs: document condition without exposing an address
Photograph the item and protective packing separately from the label. Remove names, addresses, barcodes and tracking tokens from public images while keeping originals privately.
Case 19 — Strap compatibility: width is only the first measurement
Limit of the answer in “Strap compatibility: width is only the first measurement”: “Measure the lug opening and document bar diameter,…” is an excerpt from the discussion, not an independent verification. A reader needs the relevant original material before treating an interpretation as established. Review focus: scope. Keep the stated question separate from any broader claim.
Correction note for “Crystal reflections: why a dark patch is not a coating test”: retain the wording beginning “No single lighting setup settles…” in the record. If later material changes it, add the date, the changed wording and the source for that change; do not invent a completed correction here. Keep the stated question separate from any broader claim.
Treat the comparison as inconclusive. Repeat with equal light source, charging duration, elapsed time and camera settings; disclose conditions rather than assigning an unsupported quality score.
Add lug-to-lug, thickness and lug width as separate rows. Diameter alone tells you little about wearability. Two cases 2mm apart in diameter can be within 1mm of each other lug to lug, and that number decides whether the watch overhangs a small wrist. Also give the source for each figure: manufacturer sheet, caliper measurement, or catalogue listing.
Case 33 — QC checklist: prioritise observable faults over pixel hunting
Clarification for “QC checklist: prioritise observable faults over pixel hunting”: the point beginning “Start with function, legibility, assembly and…” belongs to the question as written. It should not be read as a report that a new check, purchase or experiment has been completed. Review focus: scope. Keep the stated question separate from any broader claim.
Case 33 — A maintenance log that remains useful after a sale
Method note for “A maintenance log that remains useful after a sale”: use “Keep the date, work performed, provider invoice reference…” as a row heading in a proposed working record. Put the statement, its supporting source or measurement, and any unresolved detail in separate fields. This proposes a format; it supplies no additional evidence. Keep the stated question separate from any broader claim.